Skip to main content

Breaking Rock with Plasma: Two ATCE 2026 Papers on Geothermal Stimulation and Lower-Carbon Hydraulic Fracturing

What if a short electrical discharge could help create flow pathways in granite and reduce the pressure needed to initiate a hydraulic fracture?

At SPE ATCE 2026 in Houston, I will present two complementary papers exploring nanoparticle-enhanced pulsed-power plasma stimulation. One examines laboratory evidence of fracture creation in granite for Enhanced Geothermal Systems (EGS). The other uses numerical modeling to investigate how near-wellbore preconditioning could change hydraulic-fracturing pressure requirements and pumping energy.

Together, the studies connect a physical mechanism with two engineering questions: can we improve connectivity in tight geothermal rock, and can we reduce the work required to begin and sustain a fracture treatment?

How nanoparticle-enhanced plasma stimulation works

Pulsed-power plasma stimulation releases stored electrical energy through electrodes in a conductive fluid. The discharge forms a plasma channel and generates a rapid pressure pulse that loads the surrounding rock within microseconds.

Conventional wire-based systems consume a fusible link during discharge. Our research investigates nanoparticle-containing fluids that support multiple pressure peaks within a single discharge. This distinction matters: multiple peaks during one event do not, by themselves, demonstrate repeated downhole operation without maintenance. The geothermal paper focuses on the response within a discharge, with further operational testing still needed.

Paper 1: Creating fracture pathways in granite for geothermal circulation

SPE-233917-MS: “Nanoparticle-enhanced Pulsed Power Plasma Stimulation to Generate Fracture Networks in Granite Reservoirs for Enhanced Geothermal Systems.”

EGS development depends on connected fractures that allow injected fluid to circulate through hot rock. This study investigates how nanoparticle-enhanced plasma stimulation changes granite using pressure measurements, rock-property testing, CT imaging and thin-section microscopy.

The laboratory results show rapid, high-amplitude loading. Discharges of 10–16 kJ exceeded approximately 100,000 psi within 10 microseconds. Multiple pressure peaks extended plasma activity to approximately 60 microseconds, compared with less than 15 microseconds for the wire-based comparison.

Following 16 kJ stimulation, the presentation reports approximately 11-fold matrix-permeability enhancement and 39-fold fracture-permeability enhancement in tested samples. These measurements provide evidence that the treatment can create pathways that improve flow through granite at laboratory scale.

Thermal conductivity also decreased after stimulation, consistent with fracture creation and reduced solid-grain contact. That change alone does not establish better geothermal heat extraction. Reservoir performance will depend on sustained fracture conductivity under stress, circulation behavior and the evolution of heat transfer over time.

The next step is to evaluate how these laboratory observations translate to downhole conditions, including treatment radius, fluid stability, hardware durability and long-term thermal performance.

Paper 2: Reducing fracture-initiation pressure and pumping work

SPE-234114-MS: “Breaking Rock with Pulsed-Power Plasma Stimulation for Lower-Carbon Hydraulic Fracturing.”

The second paper asks a different question: if plasma stimulation preconditions rock near the wellbore, how much could it reduce the pressure and energy required for a subsequent hydraulic-fracturing treatment?

The workflow uses Los Alamos National Laboratory’s HOSS finite-discrete element modeling to calculate the radial extent of stimulation in granite. It then transfers that extent into a treating-pressure simulator. The comparison holds the pumping schedule and other prescribed treatment conditions consistent, allowing us to examine the consequence of the preconditioned zone.

In the modeled 6-ft treatment-depth case, bottomhole initiation pressure decreased from 13,220 psi to 7,018 psi. Peak surface pressure decreased from 11,263 psi to 8,164 psi. The modeled initiation response shifted toward reopening preconditioned flaws, suppressing the distinct breakdown peak.

The reduction during sustained pumping was smaller: approximately 196 psi, or 2.4%, in the reported propagation-period comparison. Over the full stage, modeled hydraulic work decreased by approximately 2.44%. Using the study’s diesel conversion assumptions, that corresponds to approximately 31.7 gallons of diesel and 0.323 tonnes of direct pump-side CO₂ avoided per stage.

These are numerical estimates, rather than demonstrated field savings or net lifecycle emissions reductions. A net environmental assessment must also account for the electrical discharge, materials and deployment energy.

The strongest modeled benefit is the reduction in the initiation-pressure requirement. Fracture half-length and width changed only slightly. This result points to a potential role in relieving breakdown-pressure constraints, rather than increasing the size of the created hydraulic fracture.

Why the two papers belong together

The laboratory study examines fracture creation and changes in granite properties. The modeling study examines how a preconditioned region could affect a subsequent pumping operation.

Their combination helps define both the opportunity and the questions still requiring validation. For geothermal applications, the priority is connected flow under reservoir conditions. For hydraulic fracturing, the priority is whether preconditioning can reliably reduce initiation pressure and near-wellbore entry losses.

The modeling also highlights how this approach could complement lower-carbon pumping fleets. Changing the power source reduces emissions per unit of delivered energy. Reducing pressure requirements can reduce the energy demanded by the treatment. The actual combined benefit will require field measurements and a complete energy balance.

Join the discussion at ATCE 2026

I invite colleagues working in hydraulic fracturing, geothermal engineering, geomechanics and stimulation technology to attend and discuss these studies.

Venue: George R. Brown Convention Center, Houston, Texas
Conference dates: October 21–23, 2026
All presentation times below are Houston local time (CDT).

Paper Presentation Room Technical session
SPE-234114-MS Wednesday, October 21, 2:25–2:50 p.m. 361 BECF Stimulation and Chemical Treatment
SPE-233917-MS Thursday, October 22, 8:30–8:55 a.m. 361 AD Next-Generation Geothermal Systems: Materials, Modeling, and Performance

 

Explore ATCE 2026 and register

Technical highlights are drawn from the supplied ATCE presentation decks. Presentation slots and rooms follow the supplied technical-program screenshots.